-
246, Siemens SINAMICS G110M Functions 8.10 Safe Torque Off (STO) safety function SINAMICS G110M Operating Instructions 246 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD 8.10.3.2 Protection of the settings from unauthorized changes The safety functions are protected against un…
-
300, Alarms, faults and system messages 11.5 List of alarms and faults SINAMICS G110M Operating Instructions 300 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD Number Cause Remedy A07805 Drive: Power unit overload I2t • Reduce the continuous load…
-
326, Appendix A.7 Acceptance tests for the safety functions SINAMICS G110M Operating Instructions 326 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD Figure A-7 Acceptance test for STO (basic functions) Procedure To perform an acceptance test of the ST…
-
174, Functions 8.4 Setpoint sources SINAMICS G110M Operating Instructions 174 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD Interconnecting the fixed speeds with a main setpoint Figure 8-12 Fixed speeds as setpoint source Table 8- 5 Setting…
-
193, Functions 8.6 Motor control SINAMICS G110M Operating Instructions Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD 193 Parameter Explanation p3846 Friction characteristic plot ramp-up/ramp-down time (factory setting: 10 s) Ramp-up/ra…
-
127, Siemens SINAMICS G110M Configure fieldbus 7.2 Communication via PROFINET SINAMICS G110M Operating Instructions Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD 127 Further information on PROFINET can be found on the Internet using the following links: – General in…
-
68, Installation 4.3 Electrical Installation SINAMICS G110M Operating Instructions 68 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD Figure 4-11 SINAMICS G110M CU240M USS terminal diagram
…
-
62, Installation 4.3 Electrical Installation SINAMICS G110M Operating Instructions 62 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD The ground connections ① represent the conventional grounding system for the drive components. They are made with standard, …
-
250, Functions 8.10 Safe Torque Off (STO) safety function SINAMICS G110M Operating Instructions 250 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD Figure 8-43 Interconnecting "STO active" in Startdrive 2. Select the signal that matches your part…
-
189, Functions 8.6 Motor control SINAMICS G110M Operating Instructions Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD 189 8.6.2.3 Optimizing the speed controller Optimum control response - post optimization not required Preconditions for assessi…
-
101, Siemens SINAMICS G110M Commissioning 5.2 Basic commissioning SINAMICS G110M Operating Instructions Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD 101 Figure 5-10 Macro 9 - Motorized potentiometer (MOP) Figure 5-11 Macro 12 - Two-wire control with method …
-
114, Siemens SINAMICS G110M Commissioning 5.2 Basic commissioning SINAMICS G110M Operating Instructions 114 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD Setting the AS-i address of slave 2 1. Press the button; the display shows the text SEArcH followed by uSE 0 . …
-
176, Siemens SINAMICS G110M Functions 8.5 Setpoint calculation SINAMICS G110M Operating Instructions 176 Operating Instructions, 04/2015, FW V4.7.3, A5E31298649B AD 8.5 Setpoint calculation 8.5.1 Overview of setpoint processing The setpoint can be modified as follows using the setp…
