Chicago Electric 98199 Set Up And Operating Instructions Manual

5, Chicago Electric 98199 Page 5SKU 98199 For technical questions, please call 1-800-444-3353. or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter onl…

17, Chicago Electric 98199 Page 17SKU 98199 For technical questions, please call 1-800-444-3353. pointer is exactly on 90º. Retighten the screw. Adjusting the Bevel Angle For making accurate cuts, the Saw 1. Blade must be adjusted to be exactly vertical to the Table. To check the angle, have …

18, Page 18SKU 98199 For technical questions, please call 1-800-444-3353. Troubleshooting Problem Possible Causes Likely Solutions Tool will not start No power at outlet.1. Cord not connected.2. Check power at outlet.1. Check that cord is plugged in.2. Tool operates sporadica…

11, Chicago Electric 98199 Page 11SKU 98199 For technical questions, please call 1-800-444-3353. cut. Unlock the Slide using the Slide Lock Wing Screw before making a cut if the work material is too wide to “chop”. To rotate the Table, press down the 3. Miter Thumb Lever, rotate the Table to …

6, Page 6SKU 98199 For technical questions, please call 1-800-444-3353. Some dust created by power sand-17. ing, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of Cali- fornia] to cause cancer, birth defects or other…

4, Chicago Electric 98199 Page 4SKU 98199 For technical questions, please call 1-800-444-3353. DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed…

10, Page 10SKU 98199 For technical questions, please call 1-800-444-3353. Mounting the Saw The Miter Saw must be mounted on a support before use. This may be a commercially available support or home made saw table. There are bolt holes provided in each of the four le…

19, Page 19SKU 98199 For technical questions, please call 1-800-444-3353. PARTS LIST Part# Description Qty 1 Bolt M6X25 2 2 Base 1 3 Extension Arm 2 4 Screw 2 5 Feet 4 6 Bolt M8X50 1 7 Bolt M5X10 4 8 Spring Washer 8 9 Flat Washer 4 10 Plate 1 11 R…

2, Page 2SKU 98199 For technical questions, please call 1-800-444-3353. CONTENTS IMPORTANT SAFETY INFORMATION ............................ 3 GENERAL TOOL SAFETY WARNINGS ......................................3 MITER SAW SAFETY WARNINGS ....5 VIBRATION SAFETY .................…

15, Page 15SKU 98199 For technical questions, please call 1-800-444-3353. Figure 2 3. Use the supplied Wrench to remove the Center Cover Fixing Bolt holding the Center Cover in place by turning it counterclockwise. (See Figure 2.) Figure 3 4. Remove the Safety …

13, Page 13SKU 98199 For technical questions, please call 1-800-444-3353. Align the marked location of the cut 5. on the work material with the saw blade. Be aware that the Saw Blade will remove material from the cut equal to the width of the blade. This is the “ker…

12, Chicago Electric 98199 Page 12SKU 98199 For technical questions, please call 1-800-444-3353. To make a miter cut, loosen the Miter 2. Lock Knob by turning it approximately 1/4 turn counterclockwise. Press down the Thumb Lever to unlock the Table. While holding the Thumb Lever down, move…

14, Page 14SKU 98199 For technical questions, please call 1-800-444-3353. MAINTENANCE AND SERVICING Procedures not specically explained in this manual must be performed only by a qualied technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the …

16, Page 16SKU 98199 For technical questions, please call 1-800-444-3353. Figure 7 8. Reinstall a new Blade on the Arbor. (See Figure 6.) Be sure to match the direction marked on the new blade with the direction marked on the saw Blade Housing. Replace the Outer Flange an…

1, Chicago Electric 98199 10” COMPOUND SLIDE MITER SAW Model 98199 SET UP AND OPERATING INSTRUCTIONS Distributed exclusively by Harbor Freight Tools ® . 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this produc…