Danfoss VLT DriveMotor FCP 106 Design Manual

8, 1.5.2 CE Mark Illustration 1.1 CE The CE mark (Communauté Européenne) indicates that the product manufacturer conforms to all applicable EU directives. The EU directives applicable to the design and manufacture of drives are listed in Table 1.4. NOTICE The CE …

62, Danfoss VLT DriveMotor FCP 106 Extreme running conditions............................................................. 32 F Feedback conversion.......................................................................... 19 Filter Motor cable length...........................................................…

5, 4.1.5 Automatic motor adaptation (AMA) 40 4.1.6 Fan Application with Resonance Vibrations 41 4.2 Energy-saving Examples 41 4.2.1 Why Use a Drive for Controlling Fans and Pumps? 41 4.2.2 The Clear Advantage - Energy Savings 41 4.2.3 Example of Energy Savings 42 …

31, Danfoss VLT DriveMotor FCP 106 3.3.2 Harmonics Emission Requirements For equipment connected to the public supply network, compliance with the following standards is required: Standard Equipment type Power size 1) IEC/EN 61000-3-2, class A Professional 3-phase balanced equipment, only up to …

46, Danfoss VLT DriveMotor FCP 106 m 3 /h Distribution Valve regulation Drive control % Hours Power Consump- tion Power Consump- tion A 1 –B 1 [kWh] A 1 –C 1 [kWh] 350 5 438 42.5 18.615 42.5 18.615 300 15 1314 38.5 50.589 29.0 38.106 250 20 1752 35.0 61.320 18.5 32.412 200 20 1752 31.5…

13, 2.1.3 Electrical Overview 195NA507.11 L1 L2 L3 PE 3-phase power input +10 V DC 0–10 V DC - 0/4–20 mA 0/4–20 mA 0–10 V DC - 50 (+10 V OUT) 53 (A IN) 54 (A IN) 55 (COM A IN/OUT) 42 0/4–20 mA A OUT/DIG OUT 45 0/4–20 mA A OUT/DIG OUT 12 (+24 V OUT) 18 (D…

22, Danfoss VLT DriveMotor FCP 106 1 2 z z z L1 L2 L3 PE U V W C S I 2 I 1 I 3 I 4 C S C S C S C S I 4 C S z PE 3 4 5 6 175ZA062.12 1 Ground wire 4 Drive 2 Shield 5 Shielded motor cable 3 AC mains supply 6 Motor Illustration 2.18 Equivalent Diagram: Coupling of Capacitors, which Generates Le…

52, 6.1.2 Dimensions e95na418.11 CC B A a X Y Z Z Illustration 6.2 FCP 106 Dimensions Enclosure type Power 1) [kW (hp)] Length [mm (in)] Width [mm (in)] Height [mm (in)] Cable gland diameter Mounting hole Normal lid High lid for VLT ® PROFIBUS DP MCA 101 option 3x380–…

37, 3.6.3 Cooling Drives dissipate power in the form of heat. Adhere to the following recommendations for eective cooling of the units. • Maximum air temperature to enter the enclosure must never exceed 40 °C (104 °F). • Day/night average temperature must…

14, 2.1.4 Control Terminals and Relays 195NA458.12 5 7 1 2 4 3 6 1 Control terminals 2 Relay terminals 3 UDC+, UDC-, Line (L3, L2, L1) 4 PE 5 LCP connector 6 VLT ® PROFIBUS DP MCA 101 7 VLT ® Memory Module MCM 101 Illustration 2.5 Location of Terminals and Relays, MH1 195NA409…

10, Danfoss VLT DriveMotor FCP 106 WARNING DISCHARGE TIME The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be present even when the warning LED indicator lights are o. Failure to wait the specied time after power has been removed bef…

35, • The load drives the motor at constant output frequency from the drive. That is, the load generates energy. • During deceleration (ramp-down) when the inertia moment is high, the friction is low, and the ramp-down time is too short for the energy to be dissi…

48, Danfoss VLT DriveMotor FCP 106 Event 1 True (1) Action 1 Select Preset (10) Start command State 0 Stop command Event 4 False (0) Action 4 No Action (1) State 2 State 1 Event 2 On Reference (4) Action 2 Start Timer (29) Event 3 Time Out (30) Action 3 Select Preset ref. (11) 130BA148.12 Illustra…

18, 2.3 Control Structures In parameter 1-00 Conguration Mode, select whether open loop or closed-loop control applies. 2.3.1 Control Structure Open Loop In the conguration shown in Illustration 2.13, parameter 1-00 Conguration Mode is set to [0] Open loop. The resulting…

24, 195NA407.10 L1 L2 L3 PE 1 6 2 5 4 3 1 PLC 4 Control cables 2 Drive motor-mounted 5 Mains, 3-phase, and reinforced PE 3 Minimum 200 mm (7.87 in) clearance between control cable and mains cable. 6 Cable insulation (stripped) Illustration 2.20 EMC-compliant Electrical Installatio…

39, 3.7.2 IE and IES Classes Complete drive modules (CDM) According to the standard EN 50598-2, the complete drive module (CDM) comprises the drive, its feeding section, and its auxiliaries. Energy eciency classes for the CDM: • IE0 = below state of the art. �…